Skip to content
Get a quote
CAPABILITIES

The line, the limits, the numbers.

Everything the automatic quote checks against, published. Inside these limits it prices instantly; outside, the expert team reviews. The version is recorded on every quote.

Class 100k
cleanroom
48–590 mm
board handling
160 kV
X-ray
ALSO ON SITE
  • Box build & integration - PCBA into enclosure, wiring, final test
  • Embedded design - hardware, firmware and layout to a requirement
  • BGA rework with X-ray verification
  • RMA & lifecycle - failure analysis, repair and support
PROFILES: ASSEMBLY v4 · FAB RULES v9 · JOINT TIERS v3

Assembly profile · v4 What the placement line accepts.

Packages - 01005, 0201, PBGA, FBGA, µBGA, CSP, PoP, fine-pitch QFP/QFNYES
Board size - 48×48 to 510×590 mm; panels to 450×550YES
Board types - rigid, flex, rigid-flex; 0.6–3.2 mmYES
Solder - SAC305 lead-free and leaded; wave and selectiveYES
Feeders - smart feeders 4–72 mm, 3 vibratory stickYES
Volume - HMLV and LMHV lines; prototype to 10,000+/monthYES

Fabrication profile · v9 Automatic limits for bare boards.

Layers1–8review to 12
Board size10×10 to 400×500 mmreview
Thickness0.6–2.0 mmreview
Min trace / space0.1 / 0.1 mmreview
Min via drill0.3 mmadder + review
Copper1 oz, 2 ozreview
FinishHASL, LF-HASL, ENIG, OSPreview
MaterialFR-4 Tg 135–170, PI, AlRogers review
INSPECTION & TEST

Measured, not eyeballed.

3D SPI
Koh Young, paste height and volume on every pad, from 3.94 mil.
3D AOI
Koh Young, 25 mm height inspection, both sides.
X-RAY
Nordson Dage 160 kV / 3 W for BGA, QFN, voiding.
ELECTRICAL
ICT, flying probe, functional test to spec.

Standards we build to What each one covers.

IPC-2221
The general rules for designing a printed board: how wide a track must be for the current it carries, how far apart conductors sit for the voltage between them, and the holes, pads and clearances that follow.
IPC-2222
IPC-2221's companion for rigid boards made of FR-4 and similar laminates: the further design rules for how their layers are built up and drilled.
IPC-4101
The specification for the base materials boards are made from. Each laminate is listed on its own numbered sheet that fixes its resin, its heat rating (Tg) and its electrical properties.
IPC-6012
What a finished rigid bare board must pass: copper plating thickness, hole quality, solderability and insulation, with the tests that prove them, graded by class.
IPC-6013
IPC-6012's counterpart for flexible and rigid-flex boards, the circuits that bend.
IPC-A-600
The picture book for inspecting bare boards: what an acceptable, a borderline and a rejected board look like at each class.
IPC-4552
The specification for the ENIG finish: how thick its nickel and its thin gold layer must be, so the pads solder well and resist corrosion.
IPC-A-610
The acceptance standard for assembled boards: what a good solder joint and a correctly fitted part look like at each class. Our assembly is inspected to it.

IPC Class 1, 2 and 3

Class 1 · General electronics
Products where working is what matters and looks do not, such as toys and simple consumer gadgets. The loosest limits.
Class 2 · Dedicated service
Products expected to work reliably for a long life, such as industrial controls, appliances and communications gear. Our standard for every order.
Class 3 · High reliability
Products that must work every time, such as medical, aerospace and defence equipment. The tightest limits and the most inspection.

How the profiles are used

Who maintains them?
Our catalog team. The rules are data: versioned, and edited by the team, never by a code release.
What if my spec is outside?
It goes to the expert team for a reviewed price rather than failing. Exotic specs usually come back within two working days.
Which version priced my quote?
The quote footer records the profile and rate-table versions it was priced under, so it can always be re-derived.
Do the limits change?
They move as the line is upgraded; superseded versions are kept, so old quotes stay explainable.

Inside the limits? It prices now.

Upload a BOM and find out in minutes; boards and assembly quote through the expert team until the online flow lands.

Upload a BOMor WhatsApp +91 90035 06298